SMW Resource Memory Map

Organization comes later. Feel free to add major patches here as well.
Also feel free to suggest a good way to represent SA-1 addresses (if applicable).

Lunar Magic

RAM

Most of these addresses were adquired from Lunar Magic's help file and files floating around the internet.

Address	Size	Description
$7E0BF5	0x1	ExLevel flags (to be filled later). Used on Lunar Magic 3.00+
$7E0BF6	0x100	ExLevel RAM (to be filled later). Used on Lunar Magic 3.00+
$7E13D7	0x2	Screen vertical size. Used on Lunar Magic 3.00+
$7E1936	0x2	Screen vertical size - #$0010. Used to adjust smkdan's patch Used on Lunar Magic 3.00+
$7FC004	0x1	Legacy ExAnimations frame counter. Used to be the frame counter for every ExAnimation slot, now it's only accurate for slots 0, 8, 10 and 18.
$7FC060	0x10	Conditional Direct Map16 flags.
$7FC070	0x10	Manual ExAnimation triggers. Each byte corresponds to one manual ExAnimation slot. This block of RAM addresses isn't initialized unless you use the Trigger Init button in the ExAnimation dialog.
$7FC080	0x20	Level ExAnimations frame counter. Each byte corresponds to one slot.
$7FC0A0	0x20	Global ExAnimations frame counter. Each byte corresponds to one slot.
$7FC0F8	0x4	One Shot Exanimation triggers.
$7FC0FC	0x2	Custom ExAnimation triggers. Each bit corresponds to each custom ExAnimation slot. If a bit is on it means the trigger is enabled. This block of RAM addresses isn't initialized unless you use the Trigger Init button in the ExAnimation dialog.
$7FC00B	0x2?	Purpose unknown. Used in $0EFD00 to perform a bit 2 check.
$7F8183	0x1A4?	Used for VRAM modification. $7F8185 holds a 16-bit value. Written to on $0FB054. $7F8327 is used on $0FB054 to store either 0x01B0 or 0x200. Maybe it's related to Layer 2 BG height?
$000000	0x0	To be edited later.

ROM/Routines

SNES Address	Description
$0FF900	GFX decompression routine. It can't decompress GFX files 32 or 33. On entry: A should contain the 16-bit GFX/ExGFX file number you want to decompress. $00-$02 should contain the 24-bit address of where to decompress the data to. On exit: Processor bits are preserved. Contents of X are preserved. Contents of Y are preserved. A is not preserved.
$0EFD00	LM Routine? Does something related to Layer 2 tilemaps. Returns the value of $7E1928 in A.
$000000	To be edited later.

AddMusicK

RAM

Note: AddMusicK's RAM addresses ($7FB000-$7FB00A) are reset during the SPC Program upload.

Address	Size	Description
$7E1DFA	0x1	Command list. $01 - Jump SFX. Sounds glitched due to it overwritting part of arpeggio's RAM with unexpected data. See L_0A14 for more details. $02 - Turns on Yoshi Drums. $03 - Turns off Yoshi Drums. $04 - Grinder SFX. Potentially glitched. $05 - Disables echo effect on SFXs. $06 - Enables echo effect on SFXs. $07 - Pauses music. $08 - Unpauses music. $09-$FE - Unused $FF - Jumps to L_099C. It seems to prepare the SPC700 to receive data. Disables echo, sets delay to 0, turns off channels, resets the song number (SPC Output 2 = 0). Needs testing.
$7FB000	0x1	Current song playing.
$7FB001	0x1	Flag used to disable sample upload when switching to a new song. Reset when a song finishes being uploaded to ARAM.
$7FB002	0x2	Unused. Meant to be: ARAM/DSP Address. To write to ARAM: Set $7FB002 to the address, and $7FB004 to the value to write. Note that the address cannot be $FFxx. To write to the S-DSP: Set $7FB002 to the address, $7FB003 to #$FF, and $7FB004 to the value to write.
$7FB004	0x4	SPC Output. $F4 $05 will reset $7FB004 and $7FB005. $F9 $XX $YY will send $XX and $YY to $7FB004 and $7FB005 respectively. (Needs verification) $7FB006 and $7FB007 are unused and most likely have garbage sent by the program.
$7FB008	0x1	Unused. Meant to have the same purpose as $7E0DDA.
$7FB009	0x1	Sample count in the current song.
$7FB00A	0x400	ARAM SRCN table. Used as a buffer for the sample pointer/loop table. Could be up to 1024 bytes long, but this is unlikely (4 bytes per sample; do the math).

ROM/Routines

SNES Address	Description
$008079	UploadSPCData. This is an ever-so-slightly modified version of SMW's SPC upload routine. You can jump here at any time to upload data to the SPC. Input: $00-$02 - Address of the block to upload to ARAM $03-$04 - Position in ARAM to jump to upon completion $05-$06 - Clobbered. Unused on entry; will be the size of the transferred data when finished.
$008135	UploadSPCDataDynamic. This address needs to be checked. This is an alternate version of the upload routine. Call this if it is impossible to determine ahead of time where data will go. This routine is used to upload samples by default, but it can upload anything. Input: $00-$02 - Address of the block to upload to ARAM $03-$04 - Position in ARAM to jump to upon completion $05-$06 - Size of the data to upload (this address is NOT clobbered). $07-$08 - Address in ARAM to upload to (recommended to increment it by ($05) when you finish to upload consecutive data)

PIXI

RAM

Address	Size	Description
$000000	0x0	To be edited later.

ROM/Routines

SNES Address	Description
$000000	To be edited later.

GPS

RAM

Address	Size	Description
$000000	0x0	To be edited later.

ROM/Routines

SNES Address	Description
$000000	To be edited later.

Custom Powerups

RAM

Address	Size	Description
$7E2000	0x800	RAM with different purposes. Only uses 0x1D4 bytes at the moment.
$7E2800	0x2000	Reserved as a decompression buffer for the 5th tile GFX.
$7E4800	0x2000	Reserved as a decompression buffer for dynamic items GFX.
$7E6800	0x800	Reserved as a copy of the first 2KiB of the latest decompresed GFX file.
$7E7000	0xCFF	Free to use.
$000000	0x0	To be edited later.

ROM/Routines

SNES Address	Description
$000000	To be edited later.