We've just updated MediaWiki and its underlying software. If anything doesn't look or work quite right, please mention it to us. --RanAS
TSET1 (SPC700): Difference between revisions
From SnesLab
(→See Also: SET1) |
(Active voice) |
||
| (20 intermediate revisions by the same user not shown) | |||
| Line 7: | Line 7: | ||
|'''Speed''' | |'''Speed''' | ||
|+ | |+ | ||
| | |[[Absolute Addressing | Absolute]] | ||
|0E | |0E | ||
|3 | |3 bytes | ||
|6 cycles | |6 cycles | ||
|} | |} | ||
{| class="wikitable" style="float:right;clear:right;width:30%" | {| class="wikitable" style="float:right;clear:right;width:30%" | ||
!colspan="8"|Flags | !colspan="8"|Flags Affected | ||
|+ | |||
|[[Negative Flag|N]] | |||
|[[Overflow Flag|V]] | |||
|[[Direct Page Flag|P]] | |||
|[[Break Flag|B]] | |||
|[[Half-Carry Flag|H]] | |||
|[[Interrupt Enable Flag|I]] | |||
|[[Zero Flag|Z]] | |||
|[[Carry Flag|C]] | |||
|+ | |+ | ||
|N | |N | ||
|. | |. | ||
|. | |. | ||
| Line 31: | Line 31: | ||
|. | |. | ||
|. | |. | ||
| | |Z | ||
|. | |. | ||
|} | |} | ||
'''TSET1''' is an [[SPC700]] instruction that tests and sets bits | '''TSET1''' is an [[SPC700]] instruction that tests and sets memory bits using the [[accumulator]]. For every set bit in the accumulator, TSET1 sets the corresponding memory bit. In other words, a logical OR is performed. | ||
==== Syntax ==== | |||
<pre> | |||
TSET1 !abs | |||
</pre> | |||
Where abs is any address in the whole 64K [[bank]] of [[ARAM]]. | |||
=== See Also === | === See Also === | ||
* [[TCLR1]] | * [[TCLR1]] | ||
* [[SET1]] | * [[SET1]] | ||
* [[TSB]] | |||
=== External Links === | === External Links === | ||
# Official Super Nintendo development manual on TSET1: Table C-18 in [https://archive.org/details/SNESDevManual/book1/page/n234 Appendix C-9 of Book I] | |||
# subparagraph 8.2.3.2 of [https://archive.org/details/SNESDevManual/book1/page/n186 page 3-8-8], lbid. | |||
# anomie: https://github.com/yupferris/TasmShiz/blob/master/spc700.txt#L607 | |||
[[Category:ASM]] | [[Category:ASM]] | ||
[[Category:SPC700]] | [[Category:SPC700]] | ||
[[Category:Bit Operation Commands]] | [[Category:Bit Operation Commands]] | ||
[[Category:Three-byte Instructions]] | |||
Latest revision as of 17:41, 11 August 2024
| Basic Info | |||||||
|---|---|---|---|---|---|---|---|
| Addressing Mode | Opcode | Length | Speed | ||||
| Absolute | 0E | 3 bytes | 6 cycles | ||||
| Flags Affected | |||||||
|---|---|---|---|---|---|---|---|
| N | V | P | B | H | I | Z | C |
| N | . | . | . | . | . | Z | . |
TSET1 is an SPC700 instruction that tests and sets memory bits using the accumulator. For every set bit in the accumulator, TSET1 sets the corresponding memory bit. In other words, a logical OR is performed.
Syntax
TSET1 !abs
Where abs is any address in the whole 64K bank of ARAM.
See Also
External Links
- Official Super Nintendo development manual on TSET1: Table C-18 in Appendix C-9 of Book I
- subparagraph 8.2.3.2 of page 3-8-8, lbid.
- anomie: https://github.com/yupferris/TasmShiz/blob/master/spc700.txt#L607