We've just updated MediaWiki and its underlying software. If anything doesn't look or work quite right, please mention it to us. --RanAS
COP: Difference between revisions
From SnesLab
(clarify mostly interrupt flag) |
(moved what COP does closer to the top) |
||
| Line 35: | Line 35: | ||
|} | |} | ||
'''COP''' (Co-Processor) is a [[65c816]] instruction designed to run a co-processor command. The byte following the opcode is called the [[signature byte]] and is required by assemblers: | '''COP''' (Co-Processor) is a [[65c816]] instruction designed to run a co-processor command. COP triggers a software interrupt and control is routed to the COP handler, whose address is stored in the COP vector at $FFF4. The byte following the opcode is called the [[signature byte]] and is required by assemblers: | ||
* Signature bytes of 00h to 7Fh can be programmer-defined | * Signature bytes of 00h to 7Fh can be programmer-defined | ||
* Signature bytes of 80h to FFh are reserved for future microprocessors by the [https://www.westerndesigncenter.com/ Western Design Center]<sup>[3]</sup> | * Signature bytes of 80h to FFh are reserved for future microprocessors by the [https://www.westerndesigncenter.com/ Western Design Center]<sup>[3]</sup> | ||
| Line 41: | Line 41: | ||
The state of the [[interrupt disable flag]] has no effect on the behavior of COP although it will be set after COP runs. | The state of the [[interrupt disable flag]] has no effect on the behavior of COP although it will be set after COP runs. | ||
Some examples of the kinds of microprocessors COP could be used to communicate with include: | |||
* floating point | * floating point | ||
* graphics | * graphics | ||
Revision as of 19:57, 9 August 2024
| Basic Info | |||||||
|---|---|---|---|---|---|---|---|
| Addressing Mode | Opcode | Length | Speed | ||||
| Stack (Interrupt) | 02 | 2 bytes | 8 cycles* | ||||
| Flags Affected | ||||||||
|---|---|---|---|---|---|---|---|---|
| N | V | M | X | D | I | Z | C | |
| . | . | . | . | 0 | 1 | . | . | |
COP (Co-Processor) is a 65c816 instruction designed to run a co-processor command. COP triggers a software interrupt and control is routed to the COP handler, whose address is stored in the COP vector at $FFF4. The byte following the opcode is called the signature byte and is required by assemblers:
- Signature bytes of 00h to 7Fh can be programmer-defined
- Signature bytes of 80h to FFh are reserved for future microprocessors by the Western Design Center[3]
The state of the interrupt disable flag has no effect on the behavior of COP although it will be set after COP runs.
Some examples of the kinds of microprocessors COP could be used to communicate with include:
- floating point
- graphics
The PBR is cleared, but in native mode its previous value is pushed to the stack.
Syntax
COP sig
Cycle Skipped
- COP takes one fewer cycle in emulation mode as it doesn't need to push the program counter bank register to the stack.
See Also
External Links
- Eyes & Lichty, page 447 on COP
- Labiak, page 135 on COP
- section 7.15 of 65c816 datasheet
- snes9x implementation of COP: https://github.com/snes9xgit/snes9x/blob/master/cpuops.cpp#L2738
- https://ersanio.gitbook.io/assembly-for-the-snes/deep-dives/misc
- https://undisbeliever.net/snesdev/65816-opcodes.html#software-interrupts